Spektrum DX6i Manuel d'utilisateur télécharger pdf

Replacement Transmitter Antenna Assembly

Manual for the DX6i

NOTICE

All instructions, warranties and other collateral documents are subject to change

at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit

http://www.horizonhobby.com and click on the support tab for this product.

WARNING: READ AND FOLLOW ALL INSTRUCTIONS

This manual contains instructions for safely replacing a transmitter antenna. This

replacement antenna is a key component in a sophisticated hobby product. The

instructions require basic technical knowledge and mechanical skill. The replace-

ment should not be attempted by children or beginner hobbyists.

Do not attempt disassembly, use with incompatible components, or augment the

product in any way, outside of these instructions. Failure to follow each instruc-

tion and precaution could result in a break of signal transmission, which will

ultimately lead to damage to the product, property and/or personal injury.

Read ALL instructions. If after reading these instructions you are not conﬁdent

in your ability to replace the antenna, send the antenna and transmitter to the

appropriate Horizon Service Center where this procedure can be performed by

an authorized service technician free of charge, or contact a distributor in your

country of service.

To obtain free repair service for your Replacement Transmitter Antenna Assembly

please contact Horizon Hobby Product Support.

Note: If it is decided to submit the unit for antenna replacement, Horizon will pay the

costs of return shipping and labor associated with the replacement of the antenna.

However the cost to repair any OTHER damage done to the product may be the

responsibility of the customer, to be determined at the sole discretion of Horizon

Hobby, Inc.

INTRODUCTION

The following instructions are for replacing the antenna in a DX6i. Read them com-

pletely before beginning to replace your antenna.

Items Needed:

• New antenna assembly (SPM6830)

• Medium Phillips head screwdriver

CAUTION: Never turn the radio on when the antenna is not attached to the

module. Powering up the transmitter without the antenna attached can damage

the transmitter.

STEP 1

With the transmitter power switch in the “Off” position, remove the battery door and

the batteries from the transmitter.

STEP 2

Place the radio face down on a cushioned surface to protect it from being damaged.

Using a Phillips screwdriver, remove the 6 screws holding the transmitter case

together. All removed screws should be placed in a designated area where they

will not be lost and should be placed in a manner that will allow for ordered

reinsertion.

STEP 3

Carefully remove the back case half disconnecting the wire harness connectors from

the encoder board in the front case.

NOTICE: Observe the location of each plug being removed. Reinserting the plugs

incorrectly will result in damage to the radio.

STEP 4

With the wire harness connectors separated from the encoder board, lay the back

case half aside.

STEP 5

Carefully grasp the antenna wire near the connection point to the RF board and pull

up while wiggling slightly. The antenna should disconnect easily.

Horizon Service Center 4105 Fieldstone Road

Champaign, IL 61822 USA

877-504-0233

Online Repairs visit

www.horizonhobby.com/repairs/

Horizon Product

Support

4105 Fieldstone Road

Champaign, IL 61822 USA

877-504-0233

productsupport@horizonhobby.com

Horizon Hobby Limited Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

+44 (0) 1279 641 097

sales@horizonhobby.co.uk

Horizon Technischer

Service

Hamburger Str. 10

25335 Elmshorn

Germany

+49 4121 46199 66

service@horizonhobby.de

Horizon Hobby SAS

14 Rue Gustave Eiffel

Zone d’Activité du Réveil Matin

91230 Montgeron

+33 (0) 1 60 47 44 70

infofrance@horizonhobby.com

WWW.SPEKTRUMRC.COM

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Manual for the DX6i

1Replacement Transmitter Antenna AssemblyManual for the DX6iNOTICEAll instructions, warranties and other collateral documents are subject to change at

Page 2 - Range check procedures:

2STEP 6Remove the screw which connects the slotted metal base plate to the antenna mount using a Phillips screwdriver.STEP 7Slide the slotted antenna

Page 3 - Handbuch für DX8

3Ersatz-SenderantenneneinheitHandbuch für DX8HINWEISAlle Anweisungen, Garantien und sonstige zugehörige Dokumente können nach Ermessen von Horizon Hob

Page 4

4SCHRITT 6Entfernen Sie mit einem Kreuzschlitzschraubendreher die Schraube, die die gekerbte Metallplatte mit der Antennenhalterung verbindet.SCHRITT

Page 5 - Manuel pour la radio DX6i

5Remplacement de l’ensemble d’antenne de l’émetteurManuel pour la radio DX6iREMARQUEToutes les instructions, garanties et autres documents connexes so

Page 6

6ETAPE 6Dévissez la vis qui maintient la platine d’appui au support d’antenne à l’aide d’untournevis Phillips.ETAPE 7Sortez la platine ajourée de l’an

Page 7 - Manuale per il DX6i

7Sostituzione gruppo antenna trasmettitoreManuale per il DX6iNOTATutte le istruzioni, garanzie e altri documenti allegato sono soggetti a cambiamenti

Page 8

8FASE 6Rimuovere la vite che connette la piastra di metallo scanalato al supporto dell’antenna con un giravite Phillips.FASE 7Far scorrere la base del