Spektrum SPM4100 DX4R PRO Manuel d'utilisateur télécharger pdf (Page 21)

Spektrum DX4r prO • tranSmitter inStructiOn manual

1. Remove the batteries from the transmitter. This prevents

the possibility of accidentally causing a short during the

conversion.

2. Carefully remove the grip cover by prying with your

ﬁngers at the forward edge of the rubber grip.

3. Using the 3/32-inch hex wrench, remove the three

screws on the front of the steering housing as shown.

4. Carefully remove the steering mechanism and unplug

the steering connector. Also remove the backplate.

5. Using a small Phillips screwdriver, remove the four Phillips

screws (two per side) that fasten the grip plates in place.

Remove the grip plate that doesn’t have the buttons

attached.

6. Carefully pull out the grip plate that contains buttons D,

E and F. Using a Phillips screwdriver remove the PC board

and backplate from the grip plate. Note the positions of

the three buttons.

7. Transfer the three buttons (D, E and F) to the other “handed”

grip plate (included in the box). The buttons ﬁt in a speciﬁc

direction so that they ﬁt the external contour of the grip plate.

8. Carefully screw the PC board and backplate in place

and test that all buttons are depressing properly.

9. Place both grip plates in place and fasten them using four

Phillips screws (two per side).

10. Push the steering wheel connector through the transmitter

case to the opposite side.

11. Select the opposite “handed” steering shell and pass the

steering wheel mechanism connector through the hole in

the shell.

12. Connect the steering wheel mechanism connector to the

connector from the transmitter. Make sure the connection

is tight. Note correct polarity.

13. Fit the other handed backplate in place and secure

the steering wheel assembly in place using the three

long cap head screws.

14. Fit the grip in place and reinstall the batteries. Note that

the buttons D and E now work in reverse. You will need to

change the direction of these switches in the System menu.

CHANGING TO LEFT-HANDED CONFIGURATION

The DX4R PRO comes set up for right-handed use, but you can easily switch it to a left-handed conﬁguration.

All the parts necessary to convert to left-handed, including the grip plates, the back cover and the front shell,

are included. The included 3/32-inch hex wrench and a small Phillips screwdriver will be needed.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

The system will

not connect

Transmitter and receiver too near each other Move transmitter 8 to 12 feet (2.4 to 3.6m) from receiver

Transmitter and receiver too near large

metal objects (vehicles, etc.)

Move away from large metal objects (vehicles, etc.)

Selected model is not bound in transmitter Make sure correct model memory is selected and that

transmitter is bound to the model

Transmitter accidentally put in bind mode so

receiver is no longer bound

Rebind transmitter and receiver

The receiver goes

into failsafe mode a

short distance away

from the transmitter

Check the receiver antenna to be sure it is

not cut or damaged

Replace or contact Horizon product Support

Make sure receiver antenna is in an antenna tube and is

above vehicle

Receiver quits

responding during

operation

Low battery voltage Completely recharge battery

Loose or damaged wires or connectors

between battery and receiver

Do a check of the wires and connection between battery

and receiver. Repair or replace wires and/or connectors

Receiver loses its

bind

Transmitter accidentally put in bind mode,

ending bind to receiver

Bind transmitter to receiver

Receiver taking

longer than usual to

link with transmitter

Transmitter and receiver are operating on

Marine model

Marine receivers can take longer to link with transmitter

1 2 ... 16 17 18 19 20 21 22 23 24

Commentaires sur ces manuels

Pas de commentaire

Spektrum SPM4100 DX4R PRO Manuel d'utilisateur Page 21

Commentaires sur ces manuels

Produits connexes et manuels pour Panneau de contrôle Spektrum SPM4100 DX4R PRO