Spektrum SPMAR6335 AS3X_Programmer Manuel d'utilisateur télécharger pdf (Page 2)

™

• Setalltransmittersettingsto

default.

Important: The Aileron, Elevator

and Rudder settings in the

transmitter must remain at their

factory default values. Settings for

reverse, sub trim, travel adjustment,

expo and dual rate must be done in

the App only.

1.Installthereceiverinoneof8

possibleorientationsusingdouble

sidedtape.

2.Theservoportsmustbefacingthe

frontorrearoftheaircraft.

3.Thereceivermustbemounted

paralleltotheroll,pitchandyaw

axis(NOTANGLED).

1.Insertthebindplugintointhe

receiverbindportandpoweron

thereceiver.TheLEDshouldblink

toindicatethereceiverisinbind

mode.

2.Bindthetransmittertothereceiver

atlowthrottle.Refertoyour

transmitter’smanualfordetails

onhowtobindtoyourspecic

transmitter.

Togetmoreinformation,includingdetailsondownloading

theSpektrum™AS3X

MobileProgrammingApplication,

visitwww.SpektrumRC.com/AS3XorscanthisQRcode.

Transmitter Setup Connecting to the Receiver

Plug servo leads into assigned ports

Installing the Receiver

Binding

Getting Started

CLEAR

BACK

™

AR636 shown

1.Connecttheservoplugonthe

audiointerfacecabletotheBIND/

PROGportonyourreceiver.

2.Powerthereceiverthroughany

openchannel.

3.Connecttheaudioplugonthe

interfacecabletotheaudiojack

onyourmobiledevice.Thevolume

MUSTbeturneduptofull.

4.Ensureyouhavesecurereceiver

dataportandaudiodataport

connections.

Ifthereceiverisbeingconnected

forthersttime,theAppwill

automaticallyopeninModelWizard

intheModelSetupscreen.

*Minimum system requirements:

iOS 6.0, iPhone 4, iPod 4th gen and Android 4.0

*Does not apply to iOS Devices.

If your Android device does not recognize the receiver*

1.Ensureyouhavesecurereceiverdata

portandaudiodataportconnections.

2.Disconnecttheaudioplugfromthe

device.

3.Separatetheservoplugsinthemiddle

oftheinterfacecable.

4.Flipthedeviceservoplug180degrees

andre-connecttheservoplugs.

5.Re-connecttheaudioplugtothe

device.

Normal Model Type

• Port1:Throttle

• Port2:Aileron

• Port3:Elevator

• Port4:Rudder

• Port5:Gear/Flap

• Port6:Left

Aileron

(ifequippedwith

dualservos)

Delta /

Elevon Model Type

• Port1:Throttle

• Port2:Right

Aileron

• Port3:Left

Aileron

• Port4:Rudder

• Port5:Gear

• Port6:Aux1

Typical Servo Port Assignments*:

Port1

Bind/Prog

Port2

Port3

Port4

Port5

Port6

*AR636 shown for reference. Port assignments

will be similar for all AS3X receivers. Refer to your

receivers manual for more information.

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Spektrum SPMAR6335 AS3X_Programmer Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Spektrum SPMAR6335 AS3X_Programmer